Pechanga Inspection – ElectriCare Tools

Hidden

Date

Hidden

Time

:

Outside Temperature*

Please enter a number from 32 to 150.

Weather Condition*

Lot #

Member Name

First Last

Inspection Address

Street Address Address Line 2 City State ZIP Code

Inspector Name*

Is the system Operational?*

YES
NO
PARTIAL

Contract Type*

Installation Type*

# of Stories

Main Electrical Connection

MSP & Utility Meter Location*

ie. East side of the home or pedestal

MSP Bus Rating*

From Label if present. If label is not present, please input "N/A"

MSP Main Breaker Rating*

Tie-in Breaker Rating*

Tie-in (PV) Breaker Type

Signs and labels are permanent and constructed of durable materials that withstand all outdoor environmental conditions and have legible lettering with clear contrasting colors. NEC 690.31(E)(4)

The required Warning Label(s) are installed at the Sub Panel/Main Service Panel NEC 705.12(D)(4), 690.14(C)(2), 690.54, 690.56(B)

The required Warning Label(s) are installed at the Inverter? NEC 690.35(F) for ungrounded systems NEC 690.5(C) for grounded systems

Required Warning Label(s) are installed at the DC Disconnects/Combiner boxes NEC 690.53, 690.14(C)(2), NEC 690.35(F) for ungrounded systems, NEC 690.17(4) for grounded systems

Required Warning Label(s) are installed at the AC Disconnect. NEC 690.14(C)(2), 690.54, 690.56(B), 705.12(D)(4) when fused or line side tap

Describe System Grounding at POC*

ie. The equipment-grounding conductor (EGC) is continuous to all metal components and connected to the main grounding electrode conductor per NEC 250, 690 Section V.

Additional Information*

Visible Concerns*

Inverter

Inverter Architecture*

Number of Inverters*

If Micro Inverter, please return to this section once on the roof.

Inverter(s) Location(s)*

Inverter Operational?*

YES
NO
PARTIAL

Inverter manufacturer*

Inverter Model(s)*

If Micro inverters, please return to this section once on the roof.

Inverter(s) SN(s)*

If Micro inverters, please disregard

Inverter Listed UL1741?

YES
NO
N/A

Number of Strings to inverter

String(s) DC Voltage measured at the inverter or combiner

AC Output Voltage measured at the inverter or combiner

Min 36" clearance required around equipment per NEC 110.36(A)?

YES
NO

Is the inverter in Direct Sunlight?

YES
NO

Is a DC disconnect present?

Is an AC Disconnect present?

Is the AC Disconnect within 10 Feet of Inverter*

YES
NO

AC Disconnect Size

(Amps) From label

Monitoring System Installed?

YES
NO

Describe System Grounding at Inverter*

ie. The equipment-grounding conductor (EGC) is continuous to all metal components and connected to the main grounding electrode conductor per NEC 250, 690 Section V.

Battery Information(if any)

System Wiring

Is ground-level conduit property secured

Standard building wire conductors and appropriate wiring methods utilized per NEC 690, 110.14(A)

Conductors are clearly marked. Grounded conductors are marked white or gray and equipment grounding conductors (EGC) shall be green, green/ yellow, or bare. NEC 200.6, 250.119, 310.110

Any signs of damaged or improper wiring?

Additional Wiring Recomendations

Roof/Ground Overview

Roof Material

Roof/Ground conductors properly sized and rated for 90 degrees C

Nonmetallic-sheathed conductors and cables secured within 12 inches of each box, cabinet, conduit body or other termination NEC 334

Conduit rated for location with supports properly spaced for size and type of conduit NEC 358, NEC 352, 350.22

Minimum bending radius of the USE-2 cable or PV Wire is no more than 5x the diameter of the cable NEC 334.24

All PV Source Circuit free-air conductors have 90 degree C, sunlight, and wet service ratings. Single-conductor cable type USE-2 and listed and labeled as PV wire permitted in PV source circuits NEC 690.31(B)

Strain relief fitting used at the junction box or the transition into conduit

DC PV source circuits run inside the building and they are in metal conduit from the point of penetration into the building to the first accessible disconnect NEC 690.31(E)

Roof Condition

Number of Modules on Site*

Module Type*

Manufacturer and Model Number

Module nameplate Rating (W)

Any Visible Module Damage?*

NO
YES

Module UL1730 Rating

YES
NO

PV modules are properly grounded with lugs on each panel or approved equivalent grounding method is used

YES
NO

Rapid Shutdown Installed?

YES
NO

RSD Type

Number of Arrays*

Array Azimuth(s)

Support with photo

Array Tilt

Support with photo

Array Shading

Type of Racking Installed

Racking Condition

Racking installed level and properly secured?

YES
NO

Modules passed hand lift test?

YES
NO

All components are properly tightened.

Distance from roof to lowest point of array*

Support with photo

Junction Boxes Installed

YES
NO

Junction box(s) rated for exterior application (NEMA certified)

Junction box(s) securely installed

Required Warning Label(s) used at the Junction Box. NEC 690.31(E)(3), NEC 690.35(F) for ungrounded systems, NEC 690.17(4) for grounded systems

Micro Inverters, Optimizers and RSD Properly secured to modules or rail*

Conduit supports rated for the installation and properly installed*

Has proper wire management been excercised?*

Any alterations made to the modules?*

ie. drilling module frames

Conduit penetrations properly sealed

YES
NO

Is conduit properly secured

Additional Notes and Recommendations